CRE - a direct operated proportional pressure control valve, in cartridge version, allowing the valve's application in blocks and panels with a D-10A type seat.

The valve can be used, as a pilot stage, for the remote control of two-stage pressure control and pressure reducing valves. The adjustment of pressure can be continuous, in proportion to the current, supplied to the solenoid.

The valve can be controlled directly, by a current control power supply unit, or by a specific electronic control unit, for the full exploitation of the valve's capabilities.

Max press: up to 250 bar.

PDE3 (PRED3) - a direct operated, proportional pressure control CETOP03 valve, with a standard ISO 4401 mounting interface.

The valve is suitable for two-stage valves piloting, or pressure control in hydraulic circuits. This valve is equipped with a mechanical pressure limitation feature, which allows ensuring higher safety during the performance. The valve can be directly controlled by a current control supply unit, or by an electronic control unit, for the full exploitation of the valve's capabilities.

Max press: up to 350 bar.

PDE3G* (PRED3G) - a direct operated pressure control valve with an integrated electric proportional control and ISO 4401 standard mounting interface.

The valve is suitable for two-stage valves piloting, or pressure control in hydraulic circuits. Valves are available with different types of electronics: analog or Fieldbus interfaces:
„GL“ - analog, IO-link, and CanOpen interfaces.
„GH“ - Fieldbus communication.

Max press: up to 350 bar.

PDE3J* (PRED3J) - direct operated, pressure control valve with an integrated electric proportional control and a standard ISO 4401 mounting interface.

The valve is suitable for two-stage valves piloting, or pressure control in hydraulic circuits. Valves are available with different types of electronics: analog or Fieldbus interfaces:

"JL" - analog, IO-link, and CanOpen interfaces.
"JH" - Fieldbus communication.

Max press: up to 350 bar.

PRE3 - pilot operated proportional,  CETOP 03 pressure control valve, with a standard ISO 4401 mounting interface. This valve is equipped with a mechanical pressure limitation feature, which allows ensuring higher safety during the performance.

The valve is suitable for pressure modulation in hydraulic circuits. It can be controlled directly (by a current control supply unit), or by an electronic control unit, for the full exploitation of the valve's capabilities.

Max press: up to 350 bar.

PRE3G* - pilot operated pressure control valve with electric proportional control controlled by an integrated digital amplifier, and a standard ISO 4401 mounting surface. The valve is suitable for pressure modulation in hydraulic circuits.

Valves are available with different types of electronics:

"GL" - analog, IO-link, and CanOpen interfaces.
"GH" - Fieldbus communication.

PRE* - pilot operated proportional pressure relief valves with a standard ISO 6264 (CETOP RP 121H) mounting interface.

Normally, these valves are used to control pressure in a hydraulic circuit and to enable the use of the pump's full flow rate, even when settings are reaching calibrated values. The two-stage design and wide passages, ensure the reduction of pressure drops, thereby improving the system's energy performance.

These valves can be controlled directly (by a current control supply unit), or via relevant electronic control units, for the full exploitation of the valve's capabilities. Valves are fitted with a manual pressure relief valve, which has a factory set to ≥15% of the maximum value of the pressure control range.

Max flow: up to 500 l/min.
Max press: up to 350 bar.

PRE*G - pilot operated proportional pressure relief valves, with an integrated electric proportional control, and a standard ISO 6264 (CETOP RP 121H) mounting interface.

Normally, these valves are used to control pressure in a hydraulic circuit and to enable the use of the pump's full flow rate, even when settings are reaching calibrated values. The two-stage design and wide passages, ensure the reduction of pressure drops, thereby improving the system's energy performance. Valves are fitted with a manual pressure relief valve, which has a factory set to ≥15% of the maximum value of the pressure control range.

The valves are available with a command signal (in voltage or current), and with on-board electronics (with an internal enable, an external enable or a 0V monitor on pin C.)

Max flow: up to 500 l/min.
Max press: up to 350 bar.

PRE*J - pilot operated proportional pressure relief valves with integrated electronics and a standard ISO 6264 (CETOP RP 121H) mounting interface.

These valves are used to control pressure in a hydraulic circuit and to enable the use of the pump's full flow rate, even when settings reach calibrated values. The two-stage design and wide passages ensure reduced pressure drops, thereby improving the system's energy performance.

Valve has a manual pressure relief valve, which is factory set to ≥15% of the maximum value of the pressure control range. The valves are controlled via a command signal (in voltage or current), and with on-board electronics (with an internal enable, an external enable or a 0V monitor on pin C.) The pressure's transmitter is monitored on pin F. The valves are easy to install. The driver manages digital settings directly. Valves can be adjusted and customized for special applications by using the optional kit.

Max flow: up to 500 l/min.
Max press: up to 350 bar.

MZE - 3-way pilot operated proportional pressure reducing valves designed as modular versions with a standard ISO 4401 (CETOP RP121H) mounting interface.

The valves are used to reduce pressure in the secondary circuit branches, ensuring the stability of the controlled pressure, as the secondary pressure is regulated regardless of the flow that flows through the valve.

Pressure can be modulated continuously proportionally to the current supplied to the solenoid. The valve is only available with an internal drain on the T line, inside the valve.

The valve can be controlled directly (by a current control supply unit), or by an electronic control unit, for the full exploitation of the valve's capabilities.

Max press: up to 230 bar.

ZDE3 - direct operated proportional pressure reducing valves with a standard SO 4401 (CETOP RP121H) mounting interface.

The valves are used to reduce pressure in the secondary circuit branches. In such a way, ensuring the stability of the controlled pressure; as the secondary pressure is regulated regardless of the flow, that flows through the valve.

The valve can be controlled directly (by a current control supply unit), or via relative electronic control units, for the full exploitation of the valve's capabilities.

DZCE* - proportional pressure reducing valves with a standard ISO 4401 (CETOP RP121H) mounting interface.

Pressure reducing valves, which not only reduce the pressure from line P to A, but also the flow, returned from A to T; if the pressure in the output circuit (line A) is higher than the set value (e.g. a hydraulic counterweight or load balancer). The pressure can be modulated continuously, in proportion to the current supplied to the solenoid.

Valves can be controlled directly or through specific electronic control units, for the full exploitation of the valve's capabilities.

Size: CETOP P05, ISO 4401-05 (CETOP R05), ISO 4401-07 (CETOP 07) and ISO 4401-08 (CETOP 08).
Max flow: up to 500 l/min.